Metallurgical Industry Oil Fired Gas Steam Boiler
HOT
Capacity:1-20t/h
Rated thermal efficiency: 100-104%
Fixed working pressure: ≤1.6MPa
Applicable fuel:natural gas etc.
HOT
Capacity:0.7-14MW
Rated thermal efficiency:96-98%
Fixed working pressure:≤1.25MPa
Applicable fuel:Natural gas, light oil, etc.
HOT
Capacity:0.7-2.8Mw
Rated thermal efficiency: 97.2-106%
Fixed working pressure:0.1MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:2.8-7.0Mw
Rated thermal efficiency:≥105.5%
Fixed working pressure:-0.02MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:99Kw
Rated thermal efficiency:97.2-104.4%
Fixed working pressure:1.0MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:0.5-4.0 t/h
Rated thermal efficiency:98%
Fixed working pressure:≤1.25MPa
Applicable fuel:electric energy
Boiler or steam pipe insulating : 3726: Boiler scaling: 3620: Boilermaking: 5183: Furnace installation-hot water or steam-3169: Furnace manufacturing-oil or gas fired: 2501: Furnishing goods manufacturing NOC: 2881: Metallurgical research or analytical laboratory: 8742Get Price
Supercritical boiler. 3,500 to 4,500 psi steam turbine. ESP or fabric filter. Wet lime or limestone FGD. Low NO x burners + SCR. GROUP 1 SYSTEMS. LEBS (2000) 42. Supercritical boiler. 4,500 psi steam turbine. Advanced flue gas cleanup + combustion controls a. PFBC-1 (2003)-40. Bubbling and circulating bed PFBC units. 1,800 psi steam turbine Get Price
High thermal efficiency of up to 90% when oil-fired and 89% when gas-fired Combustion equipment to suit a wide range of oil viscosities and gas compositions Designed and manufactured to latest European Standard (EN12953) for a design pressure of 1 100 kPa.Get Price
Jun 01, 2018 · The use of a waste heat boiler in this case allows the recovery and utilisation of the heat of the flue gas to vaporise a fluid and produce steam that can be used for energy generation through turbines and generators. The pressure and the rate of steam production mainly depends on the temperature of the waste heat.Get Price
Oct 08, 2019 · Steam coal is used as thermal coal to generate electric power. 73. Coking coal also is known as metallurgical coal, is used to produce thermal energy for steel production. 74. Thermal energy produced by Propane is used in heating homes and boiler water and for drying clothes, heating greenhouses, and livestock housing. 75.Get Price
Creep failure is an important phenomenon for steam and chemical plants which operate at high temperatures of 450 to 550°C, boilers, ovens, gas turbines, supersonic jets, rockets, missiles, and nuclear plants all working at very high temperatures. Creep failures or ruptures are easy to identify due to the deformation (necking) that occurs.Get Price
- Direct steam-type humidifiers inject boiler-generated steam directly into the air stream. These systems normally operate above 70 degrees C (158 degrees F), and Legionella cannot survive at that temperature. - Atomizing humidifiers use mechanical devices or pneumatic air to create a water mist that evaporates into the air stream.Get Price
Jun 01, 2015 · bottom ash, slag and boiler dust (excluding boiler dust mentioned in 10 01 04) 10 01 02. coal fly ash. 10 01 03. fly ash from peat and untreated wood. 10 01 04* oil fly ash and boiler dust. 10 01 05. calcium-based reaction wastes from flue-gas desulphurisation in solid form. 10 01 07. calcium-based reaction wastes from flue-gas desulphurisation Get Price
Supercritical boiler. 3,500 to 4,500 psi steam turbine. ESP or fabric filter. Wet lime or limestone FGD. Low NO x burners + SCR. GROUP 1 SYSTEMS. LEBS (2000) 42. Supercritical boiler. 4,500 psi steam turbine. Advanced flue gas cleanup + combustion controls a. PFBC-1 (2003)-40. Bubbling and circulating bed PFBC units. 1,800 psi steam turbine Get Price
It would be quite difficult to make a boiler with bloomery iron. The blast furnace only showed up around 1100. The Romans could certainly have made a Newcomen-style low-pressure steam engine; the first boilers were made of lead and copper (though they quickly switched to iron). However, those are of only mild usefulness.Get Price
Boiler tubing, the oil and gas industries, and automotive transmission components are typical applications. Secondary metallurgy Steel 's precise composition can vary from customer to customer, and steelmakers use a secondary metallurgy vessel (often referred to as a ladle furnace) between the steelmaking and casting operations to allow Get Price
Heat Recovery Steam Generators, Boiler Air Pollution Control, Boiler Services, Feedwater Heaters, Moisture Separator Reheaters, Surface Condensers Natural Gas, Oil and LPG Systems and Complete Engineering Processes. READ MORE. Wear-Resistant Parts and Composite Materials for the Coal-Fired Power Industry. READ MORE. Mahnzi. Engineering Get Price
High thermal efficiency of up to 90% when oil-fired and 89% when gas-fired Combustion equipment to suit a wide range of oil viscosities and gas compositions Designed and manufactured to latest European Standard (EN12953) for a design pressure of 1 100 kPa.Get Price
Heat Recovery Steam Generators, Boiler Air Pollution Control, Boiler Services, Feedwater Heaters, Moisture Separator Reheaters, Surface Condensers Natural Gas, Oil and LPG Systems and Complete Engineering Processes. READ MORE. Wear-Resistant Parts and Composite Materials for the Coal-Fired Power Industry. READ MORE. Mahnzi. Engineering Get Price
Feel free to reach out if you want to collaborate with us, or simply have a chat.
